Custom Cabinetry Kawana

Kawana was still rural ground known as Splitters Creek and Glenmore when Glenmore primary school opened in 1889, and it became one of Rockhampton's new suburbs after a barrage was built across the Fitzroy River at Splitters Creek in 1970 to secure the city's fresh water. The housing that followed is brick and square: 84.1 per cent of dwellings are separate houses and 58.9 per cent are owner-occupied. Cabinet boxes from that era are frequently still sound while the benchtops and fronts have dated, which makes a new top and new fronts better value here than a rebuild. Rockhampton Custom Cabinets checks the carcases first and says which way is honest. Quotes are free, itemised and in writing. Call 0485 032 128.

GET A FREE QUOTE

Custom Kitchens in Kawana

OUR STORY

Custom cabinetry Kawana, cut to the room rather than the catalogue

The range below is what gets built for a Kawana house, made to the measured room rather than ordered in fixed module sizes.

Kitchens and bathrooms

A kitchen in a 1970s Kawana house is usually a square room with a full run of shallow overheads and a separate dining area, so the gains are in storage and layout rather than in making cabinetry fit. Bathrooms are often close to a catalogue width but rarely exactly, which is where a vanity built to the opening uses the full wall instead of leaving a filler strip in the wettest part of the room.

Linen, hallway and garage storage

A brick-era house has some built-in storage but seldom enough. A linen cupboard works at 450 to 500 millimetres deep with shelves 300 to 350 millimetres apart, and a shallow 300 millimetre run along a hallway wall taken to the ceiling adds storage without narrowing the hall. Garage shelving is specified in moisture-resistant board with sealed edges and kept off the slab, because a garage here runs hotter and damper than the house.

Door and drawer-front replacement

Where the cabinet boxes are square and sound and only the fronts have dated, new doors, drawer fronts, handles and hinges change a room for a fraction of a rebuild. In Kawana this is the most common honest recommendation, because the carcases from the 1970s and 1980s are usually fine. The boxes are checked first, particularly under the sink, and where one has failed that is reported rather than covered with a new front.

What a measure in Kawana involves

A measure happens at the house. Wall lengths, floor level, window reveals and the existing plumbing and power are recorded, appliances are measured where they are staying, and board and finish samples are left in the room to be seen in its own light. The quote is itemised and written, and nothing is cut until the drawing is signed off.

Laundry Cabinets in Kawana

SERVICES WE OFFER IN Kawana

Cabinetry built for a summer wet season and 1970s brick housing

Rockhampton records about 717 millimetres of rain a year with most of it in summer, around 104 millimetres in January against 30 to 37 millimetres a month in winter, and a January mean maximum of 32.6 degrees. Kawana's housing is brick and square, which makes the work predictable and the material specification the main variable.

A summer-dominant wet season and what it does to a cut edge

Rain concentrated into a few months means a sustained humid period rather than an even average, and that is when an unsealed cut edge beside a sink, a dishwasher or a laundry tub takes up moisture and swells. Carcases are moisture-resistant board, cut edges sealed, banding heat-sealed to the panel, and the base of a sink or tub cabinet lined. On a refacing job the new fronts are built to that specification even where the originals were not.

Houses built as Rockhampton's new suburbs in the 1970s

Kawana became a suburb in the wave of development that followed the 1970 Splitters Creek barrage, and Glenmore High opened next to the old primary school in 1975 as the city's third state secondary school. The houses from that period are brick, slab or low-set, with standard 2,400 millimetre ceilings and square rooms. That means the original cabinet boxes were built into a predictable space and have usually stayed square.

Square rooms, and what that makes possible

Square rooms rule in options that an older timber home rules out. A long uninterrupted bench run, a benchtop replaced without a complicated template, and refacing with no scribing all become straightforward, which keeps labour down. It also means flat-pack is a genuinely reasonable alternative here, and where a household's budget points that way it gets recommended rather than argued against.

Laundry Cabinets in Kawana
Built-in Wardrobes in Kawana

Why choose us in Kawana

Why Kawana households choose a cabinet maker near you

Kawana is a few kilometres from the workshop, which matters most on the shorter jobs that make up a lot of the work here.

One accountable team from measure to installation

The person who measured the kitchen works for the business that builds the cabinetry and installs it, so the fit is somebody's responsibility rather than an argument between suppliers. On a benchtop replacement the cabinets are checked and levelled, the top templated after they are set, and a licensed plumber reconnects the sink against those dates rather than being chased afterwards.

Made to measure rather than modular

The nearest IKEA store is roughly 600 kilometres south near Brisbane and the Kawana address there is a click-and-collect collection point rather than a showroom with a kitchen planner. In a square brick room with standard appliances, flat-pack genuinely works and is a fair choice. Made-to-measure earns its price where an opening is an odd width, where the storage needs designing, or where the finish has to match something already in the house.

Insurance, trade standards and a free written quote

Rockhampton Custom Cabinets holds public liability cover to $20 million and trades under ABN 56 573 390 615, both checkable. Runners are specified to carry around 40 kilograms, hinges rated beyond 100,000 open-and-close cycles, carcases built from 16 to 18 millimetre board, and doors hung to a reveal of about 2 millimetres. The measure and the quote cost nothing.

Walk-in Wardrobes in Kawana

SERVICES WE OFFER IN Kawana

Kawana streets and pockets, Glenmore to Splitters Creek

Kawana covers about 7.6 square kilometres with six parks across roughly 7.8 per cent of it, and its pockets came from different stages of development.

Glenmore, the old school and the suburb's centre

Before it was a suburb this was rural land known as Glenmore, and Glenmore primary school opened in the middle of it in 1889, long before the housing arrived. Glenmore High followed in 1975 next door. The streets around the two schools hold the earliest suburban housing, where kitchens and bathrooms are now on their second refit and the carcases are often original and still sound.

Splitters Creek, the barrage and the southern end

Splitters Creek is the short stream at the south of the suburb that gave the area its first name, and the barrage built across the Fitzroy there in 1970 is the reason Kawana exists as a residential suburb at all. The southern end holds a share of the suburb's later housing, which is squarer and more predictable again, and where full kitchen replacements are more common than refacing.

The streets off Carara Drive and Scott Street

Carara Drive, Scott Street, Ash Street, Cant Street and Lutton Street run through the residential heart of the suburb. With 84.1 per cent of dwellings separate houses and 58.9 per cent owner-occupied, the work through these streets is mostly for people who live in the house rather than between tenancies, which shows in the brief: better storage and a longer-lasting specification rather than the cheapest option.

Walk-in Wardrobes in Kawana
Built-in Wardrobes in Kawana

Why choose us in Kawana

Benchtops and refacing Kawana: new tops and fronts on sound cabinets

This is the job Kawana's housing stock is built for, and it is offered less often across the trade than it should be.

When the cabinet boxes are worth keeping

The carcases decide it, not the doors. The base of the sink cabinet is checked for swelling, the cabinet beside the dishwasher for steam damage, and the whole run for racking, sagging shelves and failed fixings, with a level and square taken across the run. In brick-era housing the boxes are frequently square and sound, which is exactly when a new top and new fronts deliver most of a new kitchen for a fraction of the cost.

Replacing a benchtop on cabinets that stay

A replacement top is templated to the cabinets as they actually sit rather than ordered to a nominal size, which is why a template beats a measurement even in a square room. Compliant surfaces are quoted: laminate, natural stone, porcelain and sintered surfaces, or solid timber. Engineered stone cannot lawfully be supplied or installed anywhere in Australia. It is also the cheapest moment to change the sink and tap, because the cut-outs are being made anyway.

New fronts, handles and hinges on an existing kitchen

Refacing replaces the doors, drawer fronts, visible end panels, kickboards and handles, with hinges and runners renewed at the same time because they are the same age as the doors. New fronts are made to the measured openings, which on a kitchen built on site in the 1970s vary by several millimetres across one run. Published regional Queensland guides put a cosmetic refresh of this kind at roughly $8,650 to $21,600.

Walk-in Wardrobes in Kawana

SERVICES WE OFFER IN Kawana

Small-job cabinet maker work in Kawana: one-off pieces and repairs

Small jobs keep a sound kitchen going, and they are quoted properly rather than treated as filler.

One-off pieces and small repairs

A single cupboard, a vanity, a bank of drawers built to fit one gap, a broom cupboard with an internal power point for a stick vacuum: each is measured and quoted per piece. Repairs cover a swollen cabinet base under a leaking tap, failed drawer runners or a door that no longer sits to an even reveal. In brick-era housing the most common repair is hardware that has worn out while the cabinet itself is fine.

Matching an existing cabinetry run

Adding to cabinetry already in the house is harder than replacing it, because colour, profile and sheen all have to line up and existing doors have faded. The profile is measured off the original, the colour matched against a door removed from the house rather than a sample card, and the sheen matched separately. Where an honest match cannot be achieved, that is said rather than attempted.

Adding drawers and pull-outs to cabinets already there

A 1970s kitchen was built with shelved cupboards and no bin solution, and both can be fixed without replacing the boxes. A shelved cupboard can be converted to deep pot drawers inside the same carcase, a concealed bin pull-out fitted under the sink, a pull-out pantry built into a 300 or 450 millimetre gap, and a blind corner given a swing-out so the back is reachable. These are modest jobs that change how a kitchen works daily.

Walk-in Wardrobes in Kawana
Built-in Wardrobes in Kawana

Why choose us in Kawana

Joinery Kawana: robes, vanities and built-in storage

Outside the kitchen, the same carcases and hardware build the rest of the house.

Wardrobes and robe fit-outs

A built-in robe is made to the measured opening, with sliding doors where a bedroom is tight and hinged doors where the floor allows the swing, and the interior planned around what is actually stored. Long hang at about 1,500 millimetres takes coats and dresses, double hang at roughly 1,000 millimetres doubles capacity for shirts, and a drawer bank frees the floor a chest of drawers occupied. A closed robe in a humid summer needs a vent or a gap so it can breathe.

Vanities and bathroom storage

A vanity is built to the opening, which in a brick-era bathroom is sometimes a catalogue width and often not quite. The bowl cut-out and waste penetration are sealed, the base lined, and the kickboard sealed and removable so a slow leak shows on the floor rather than soaking into board. A mirror cabinet above returns the storage the bowl takes out of the cabinet below.

Laundry cabinetry and tub surrounds

A laundry takes more water than any room except the bathroom. Tub cabinets are built in moisture-resistant board with the cut-out sealed and the base lined, and a bench over front-loading machines turns the room into somewhere washing can be folded. A pull-out hamper, a drying rail for the wet season and a broom cupboard are the additions that get used daily and cost little during the main job.

Custom Cabinetry Services we offer In Kawana

Custom Kitchens in North Rockhampton

Made-to-measure kitchens built for Rockhampton homes, from Queenslander renovations to new Gracemere builds. Moisture-resistant board, soft-close hardware and a choice of finish, measured, built and installed by the same local team.

Laundry Cabinets in Yeppoon

Custom laundry cabinets built to fit your room, not a flat-pack's fixed sizes. Overheads, broom cupboards and benchtops that hide the washer and dryer, all in moisture-resistant board made for Rockhampton's humid summers. Local, fully insured and built to last.

Built-in Wardrobes in Yeppoon

Built-in wardrobes made to measure for the bedroom, with a proper interior fit-out instead of a single rail. Hinged or sliding doors, mirror options and drawers, scribed wall to wall so no gap is wasted. Local, insured and built by the same team.

Walk-in Wardrobes in Yeppoon

Walk-in wardrobes designed as a proper dressing room, with hanging, drawers, shoe walls and an island bench where space allows. Full custom, built around how you dress and finished to leave the door open on. Local, insured and made to measure.

Bathroom Vanities in Yeppoon

Custom bathroom vanities built for real bathrooms, with storage and basin styles to suit and the plumbing worked around rather than into. Moisture-resistant construction and sealed cut-outs for a humid climate. Compliant benchtops only, no engineered stone. Local and insured.

Custom Joinery in Yeppoon

Bespoke built-in joinery for the pieces a flat-pack cannot do: bookshelves, window seats, bar units, display cabinets and feature walls, scribed to a Queenslander's out-of-square walls and finished in laminate, timber veneer or durable two-pac by the same Rockhampton team.

Entertainment & TV Units in Yeppoon

Custom TV and entertainment units built around the screen and the AV gear: floating consoles, full floor-to-ceiling media walls and fireplace features, with proper ventilation, concealed cabling and dead-level installation by the same Rockhampton team.

Bathroom Vanities in Yeppoon

Custom home office cabinetry built around how the work happens: fitted desks at the right height, document and filing storage, overhead units and hidden cable management, scribed to fit a study, alcove or hallway nook by the same Rockhampton team.

Custom Joinery in Yeppoon

Whole-home custom storage that captures dead space: linen cupboards, mudroom drop zones, under-stair and laundry storage, garage and utility systems, scribed to fit and built with full-extension soft-close hardware by the same Rockhampton team.

Entertainment & TV Units in Yeppoon

Compliant benchtops only: laminate, natural granite and marble through licensed stonemasons, porcelain and solid timber. No engineered stone, ever. Tops are templated on site, the stonemason is coordinated and every cut-out is sealed square, so the bench performs in a humid Rockhampton kitchen.

Bathroom Vanities in Yeppoon

Commercial shopfitting and joinery for retail, offices, cafes and hospitality: counters, display, shelving, reception and back-of-house. Built commercial-grade, installed around your trading hours and lease deadline, so your tenancy opens on time and stands up to real foot traffic.

Custom Joinery in Yeppoon

Refacing swaps the doors, drawer fronts, panels and hardware onto sound existing carcases, a cost-effective update rather than a full rebuild. The carcases are assessed honestly first: where the boxes are solid it transforms a kitchen for a fraction of a replacement.

Entertainment & TV Units in Yeppoon

Bathroom Vanities in Yeppoon

Custom Joinery in Yeppoon

Custom Cabinetry In Kawana

FREQUENTLY ASKED QUESTIONS

Everything you need to know about our Custom Cabinetry In Kawana

Is refacing better value than a new kitchen in Kawana?

Frequently, yes, because the suburb's housing is brick-era and the cabinet boxes are usually still square and sound while the benchtops and fronts have dated. Published regional Queensland guides put a cosmetic refresh keeping the carcases at roughly $8,650 to $21,600 against a mid-range full renovation at about $27,000 to $48,600. The carcases are checked first, particularly the base under the sink, and the finding is reported either way rather than a reface being quoted regardless.

Can just the benchtop be replaced?

Yes, and where the carcases are square and the layout works it is one of the best-value kitchen jobs available. The new top is templated to the cabinets as they actually sit rather than ordered to a nominal size. Compliant surfaces are quoted: laminate, natural stone, porcelain and sintered surfaces, or solid timber. It is also the cheapest moment to change the sink and tap, since the cut-outs are being made anyway and a licensed plumber is already attending.

Can drawers be added to an existing 1970s kitchen?

Yes, and without replacing the boxes. A shelved cupboard can be converted to deep pot drawers inside the same carcase, a concealed bin pull-out fitted under the sink, a pull-out pantry built into a 300 or 450 millimetre gap, and a blind corner given a swing-out so the back is reachable. Those four changes account for most of what people mean when they say an older kitchen does not work, and each is a modest job.

Is flat-pack a reasonable option in Kawana?

Yes, more so than in the city's older suburbs. The housing here is brick and square with standard 2,400 millimetre ceilings, so fixed cabinet sizes fit without the tapering filler panels that spoil flat-pack in a settled timber home. Where a household's budget points that way it gets recommended on its merits. Made-to-measure earns its price where an opening is an odd width, the storage needs designing, or a finish has to match something already in the house.

What does custom cabinetry cost in Kawana?

Published regional Queensland guides put a mid-range kitchen renovation at roughly $27,000 to $48,600 with the cabinetry component commonly $12,950 to $37,800, a cosmetic refresh keeping the carcases at about $8,650 to $21,600, a laminate benchtop at $865 to $2,700 and a stone benchtop at $2,700 to $9,700. Those are regional Queensland guide ranges rather than a measurement of this market, so a written quote after a free on-site measure is the accurate figure.

Why does cabinetry here need moisture-resistant board?

Because the region's rain is concentrated in summer, around 104 millimetres in January against 30 to 37 millimetres a month in winter inside an annual total of roughly 717 millimetres, with a January mean maximum of 32.6 degrees. That sustained humid period is when an unsealed cut edge beside a sink, dishwasher or tub takes up moisture and swells. On a refacing job the new fronts are built to that specification even where the originals were not.

TESTIMONIALS

What Kawana Homeowners Say About Us

Request A Free Quote

GET A FREE QUOTE